Tripp Lite PowerVerter APS Instrukcja Właściciela Pobierz pdf (Strona 11)

To avoid overloading your Inverter/Charger, match the power requirements of the equipment you plan to run at any one time (add their total

watts)withtheoutputwattagecapacityofyourInverter/Chargermodel(seeNameplate).Donotconfuse“continuous”wattagewith“peak”

wattage ratings. Most electric motors require extra powerat start-up (“peak wattage”) than required to run continuously after start-up,

sometimesover100%more.Somemotors,suchasinrefrigeratorsandpumps, start and stop intermittently according to demand, requiring

“peak wattage” at multiple, unpredictable times during operation.

OverPower™ Feature

TrippLiteInverter/Chargersdeliverupto150%oftheirnameplate-ratedwattagefor1-60minutesunderidealbatteryandtemperature

conditions,providingamplereservepowertosupporttoolsandequipment.*

* For best results, utilize OverPower for as short a duration as possible, ensure that battery bank and cabling are able to provide full nominal DC voltage under load, and allow the inverter/charger

to cool completely before and after OverPower utilization.

DoubleBoost™ Feature

TrippLiteInverter/Chargersdeliveruptotwicetheirnameplate-ratedwattageforupto10seconds,providingtheextrapowerneededto

cold-startheavy-dutytoolsandequipment.*

* Actual duration depends on model, battery age, battery charge level and ambient temperature.

AC Input/Output Connection

Service

BeforereturningyourInverter/Chargerforservice,followthesesteps:1.)Reviewtheinstallationandoperationinstructionstoensurethat

theserviceproblemdoesnotoriginatefromamisreadingoftheinstructions.Also,checkthatthecircuitbreaker(s)arenottripped.*2.)If

the problem continues, do not contact orreturn the Inverter/Chargerto the dealer. Instead, call TrippLite at773.869.1233.A service

technician will ask for the Inverter/Charger’s model number, serial number and purchase date and will attempt to correct the problem over

thephone.3.)Iftheproblemrequiresservice,thetechnicianwillissueyouaReturnedMaterialAuthorization(RMA)number,whichis

requiredforservice.SecurelypacktheInverter/Chargertoavoiddamageduringshipping.DonotuseStyrofoambeadsforpackaging.**

Any damages (direct, indirect, special, incidental or consequential) to the Inverter/Charger incurred during shipment to Tripp Lite or an

authorizedTrippLiteservicecenterisnotcoveredunderwarranty.Inverter/ChargersshippedtoTrippLiteoranauthorizedTrippLite

servicecentermusthavetransportationchargesprepaid.MarktheRMAnumberontheoutsideofthepackage.IftheInverter/Chargeris

withinthewarrantyperiod,encloseacopyofyoursalesreceipt.ReturntheInverter/Chargerforserviceusinganinsuredcarriertothe

address given to you by the Tripp Lite service technician.

* This is a common cause of service inquiries which can be easily remedied by following the resetting instructions in this manual. ** If you require packaging, the technician can arrange to send

you proper packaging.

Your Inverter/Charger requires no maintenance and contains no user-serviceable or replaceable parts, but should be kept dry at all times.

Periodically check, clean and tighten all cable connections, as necessary, both at the unit and at the battery.

Maintenance

Ground*

• Connecttheincomingandoutgoinggroundwirestotheground(green)terminal.

AC Input

• Connect the incoming hot wire to the input hot (brown) terminal .

• Connecttheincomingneutralwiretotheinputneutral(blue)terminal.

AC Output

• Connect the outgoing hot wire to the output hot (black) terminal .

• Connecttheoutgoingneutralwiretotheoutputneutral(white)terminal.

• Replacecoverplateandtightenscrews.

* If the incoming conduit only contains two wires (hot and neutral), the incoming conduit must be bonded to the main ground lug on the

unit. In any case, the incoming conduit must be bonded to earth or vehicle ground, and the incoming conduit must be bonded to the

outgoing conduit.

Warning! Consult a qualified electrician and follow all applicable electrical codes and requirements for hardwire

connection. Disconnect both DC input and AC utility supply before attempting hardwiring. Use wire type THHN or

equivalent with minimum temperature rating of 90°C.

Hardwire Connection

Removethescrewsandcoverplateoverthehardwireterminal box.Removetheknockoutcoversclosesttothedesiredelectricalsourceand

toyourequipment.Attach½"diameterconduits(user-supplied)totheknockoutsandthreadwiresthrough.Connecttheconduitstoeach

other with the ground bond connection supplied.

OUTPUT/NEUTRAL

OUTPUT/HOT

INPUT/NEUTRAL

INPUT/HOT

GROUND

“FOR USE WITH COPPER WIRE ONLY”

1 2 ... 6 7 8 9 10 11 12

Komentarze do niniejszej Instrukcji

Brak uwag

Tripp Lite PowerVerter APS Instrukcja Właściciela Strona 11

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Zasilacze i falowniki Tripp Lite PowerVerter APS